| Internet-Draft | IoT Smart Devices Security | September 2022 |
| Wang, et al. | Expires 17 March 2023 | [Page] |
With the development of IoT, security of smart devices becomes an important issue for us to discuss. This draft proposes a security framework and detailed requirements in terms of hardware, system, data, network, and management to ensure the security of IoT smart devices. Specifically, hardware security includes the security of hardware interfaces and components. System security includes firmware security, security audit, etc. Data security includes data verification and sensitive data protection. Network security includes stream protection and session security, etc.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 17 March 2023.¶
Copyright (c) 2022 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
The new paradigm of IoT is recognized as one of the most important actors in the Information and Communication Technology industry for next years [Miorandi2012]. The introduction of IPv6 [RFC6568] and CoAP [RFC7252] as fundamental building blocks for IoT applications allow connecting IoT hosts to the internet. [RFC7744] provides an overview of relevant IoT use cases. With the development of IoT in recent years, the industry of smart devices gains great momentum, resulting in a large-scale production and application of smart devices. However, the absence of unified security standards leads to various security defense measures, which imposes huge threats on IoT security. Until today, smart devices have become favored targets for hackers, which leads to frequent security incidents. [Qiu2020] and [Neshenko2019] conducted a detailed survey on the security issues of IoT.¶
This draft proposes detailed security requirements to ensure smart devices can work in a security condition.¶
This draft proposes some basic security requirements that should be met by smart devices in IoT.¶
This draft is proposed for specifying security functions of smart devices in IoT to improve the security of devices, which can prevent devices from being maliciously exploited by attackers and safeguard users' sensitive data.¶
This draft is also applicable to instructing the design and implementation of security functions of smart devices in IoT.¶
Smart device is a kind of device that can perceive and process video data, image data or other types of data. For example, video cameras, laser radar, identity gateways, etc. Smart devices can be connected to the IoT platform directly, or through a gateway as its sub-devices.¶
Video surveillance device is a typical smart device, which can collect and process video image signals, and communicate with other devices via the internet.¶
Information that is confidential and is of actual or potential value. The loss, improperly use or unauthorized access of this information may cause harm to society, business or individuals.¶
A flaw in the specific implementation of a software (hardware or protocol) or the security strategy of a system, leaving it open to the potential for exploitation in the form of unauthorized access or malicious behaviors.¶
Check all possible passwords systematically to find the correct one.¶
Network port is an endpoint of communication in an operating system, which identifies a specific process or a type of network service running on that system, such as service ports in TCP/IP with port numbers ranging from 0 to 65535.¶
The data stream of video information in network transmission.¶
To set the administrator's password when the user uses the device for the first time, and the password must meet the requirements of password security policy.¶
The following abbreviations and acronyms are used in this draft: Abbreviations and Acronyms | Full Name --------|-----: JTAG | Joint Test Action Group IP | Internet Protocol TLS | The Transport Layer Security Protocol HTTPS | Hypertext Transfer Protocol Secure SSH | The Secure Shell Protocol SFTP | Secure File Transfer Protocol OTP | One Time Programmable Read Only Memory TEE | Trusted Execution Environment Table: Abbreviations and Acronyms¶
The framework of IoT consists of three layers. From bottom to top, they are the perception layer, the network layer and the application layer. Smart devices reside in the perception layer, aim to sense physical phenomena and translate them into a stream of information data. Furthermore, they isensenteract with IoT platform through communication modules. The framework of smart devices is shown as follow:¶
+-------------------------------------------------------+ | Application | +----------------------------+--------------------------+ | | | | Media & Algorithm library | | | | | | +-------+ +-------------+ | | | | Video | | Algorithm A | | Network | | +-------+ +-------------+ | communication | | +------+ +-------------+ | | | | Audio| | Algorithm B | | | | +------+ +-------------+ | | +----------------------------+--------------------------+ | Operating System & Bootloader | +-------------------------------------------------------+ | Hardware | |(Lens/Sensors/ISP/AI Chips/Memory/Interface/Serial port)| +-------------------------------------------------------+
The draft adopts the strategy of layered security and multi-level defense, and proposes a security function framework of smart devices, shown as follow:¶
+------------------------------------------------------------------+ | Smart Devices of IoT | | +-----------------------------------------------------+--------+ | | | +------------+ +-----------+ +-----------------+ | | | | | | Access | | Port | |Service & | N | | | | | | Security | | Security | |Protocol Security| E | | | | | +------------+ +-----------+ +-----------------+ T | S | | | | +------------+ +-------------+ +---------------+ W | E | | | | |Transmission| | Stream | | Session | O | C | | | | | Security | | Protection | | Security | R | U | | | | +------------+ +-------------+ +---------------+ K | R | | | +-----------------------------------------------------+ I | | | | +------------+ +----------------+ D | T | | | | | Data | |Sensitive Data | A | Y | | | | |Verification| | Protection | T | | | | | +------------+ +----------------+ A | M | | | +-----------------------------------------------------+ A | | | | +------------+ +------------+ +-------------+ | N | | | | | Firmware | | Security | | Password | S | A | | | | | Security | | Audit | | Management | Y | G | | | | +------------+ +------------+ +-------------+ S | E | | | | +----------------+ +----------------+ +--------+ T | M | | | | | Authentication | | Time | | Access | E | E | | | | | | | Synchronization| | Control| M | N | | | | +----------------+ +----------------+ +--------+ | T | | | +-----------------------------------------------------+ | | | | +----------------------+ +----------------+ | | | | | | Interface | | Security | HARD | | | | | | Security | | Component | WARE | | | | | +----------------------+ +----------------+ | | | | +--------------------------------------------------------------+ | +------------------------------------------------------------------+
Hardware security mainly focuses on the hardware feature of the device, including two aspects. The first one is whether there is any unused hardware interface on the device, and the second one is whether the device can provide security support better owe to the security component.¶
System security refers to the secure application of the device's software resources, including bootloader, operating system and applications.¶
Data security aims to protect the data in the device, including device management data and user business data. The special attention should be paid to the sensitive data.¶
Network security realizes the security of the connection to the IoT's network layer and protects against the attack from the network.¶
Security management is mainly about how to securely use and manage the smart devices.¶
Hardware security contains interface security and security components. Interface security refers to that the device should not expose any physical interface with security risks. Security component refers to that when designing the hardware, the hardware with security function support shall be prioritized.¶
Before the smart devices leave the factory,¶
a) JTAG debugging interface should be disabled.¶
b) Serial ports should be disabled, or improved by developing an authentication mechanism.¶
a) For the smart device, chips that support OTP, Secure boot and TEE are recommended, and the relevant security functions should be enabled.¶
b) If possible, it is recommended to add a security chip with cryptography service function. The selection of security chip should follow the corresponding national cryptography management policy.¶
System security includes firmware security, time synchronization, cryptography management, authentication, security audit and access control, etc.¶
a) The firmware should only contain the necessary components and applications.¶
b) For third-party open source software, the version without known vulnerabilities (or has been patched) should be used.¶
c) Debug codes in the device should be deleted before device leaves the factory.¶
d) Administrator should have access to check the current version of the device.¶
e) Firmware upgrading should be available.¶
f) When generated, firmware upgrade packages should be digitally signed.¶
g) The signature information of the upgrade package should be verified when upgrading.¶
The smart device should have real-time clock and support time synchronization calibration function.¶
a) The smart device should apply publicly standard algorithms.¶
b) The smart device should apply industry standard cryptographic algorithm and regularly assess and update the encryption algorithm and its strength.¶
c) The smart device should apply secure random numbers.¶
d) The smart device should forbid the hard coding of secret key.¶
e) The smart device should apply irreversible encryption algorithm in the scenario where the recovery of the password's plaintext is not required.¶
a) Users' accounts should be unique.¶
b) At least two user roles should be set: administrator and user.¶
c) When the user account is deleted, the corresponding online user should be logged out.¶
d) Permissions assigned to administrators and users should be different.¶
e) Users can manage and control the device only after successful authentication.¶
f) If adopted, a random password should be generated as default before device leaves the factory. The user should be prompted to change the default password.¶
g) If an activation mechanism is adopted, the user should set a secure password that meets security requirements when initializing the device.¶
h) Password complexity check should be in place, and the password should have at least 8 characters, with at least two kinds of the following types: numbers, lowercase, uppercase and special character.¶
i) The password entered by the user must be masked by default, and the password copying must be disabled.¶
j) The password should be encrypted when stored and transmitted.¶
k) The authentication for remote access users should be performed on the server.¶
l) The feedback should not include clear reasons for the authentication failure and should prompt the user with "user name or password error".¶
m) Illegal login lock should be applied to defend against brute force attacks during user authentication. Login attempts from the IP address or account will be rejected for a period of time if it has been failed for certain times.¶
a) For the smart device, the access to video streams should be authenticated and authorized.¶
b) Only the administrator has the privilege to import (or export) the parameter profile of the device.¶
c) Only the administrator has the privilege to use interactive command console.¶
d) The command console must not provide user management commands.¶
a) The smart device should support security audit function. Operations that need to be audited include the following:¶
Enabling or disabling the security audit function;¶
User creation, deletion or modification;¶
User login and logout;¶
Upgrade or update of the firmware;¶
Changes of the device configuration.¶
b) The audit information should include account, IP address, operation time, operation type and operation result, etc.¶
c) The handling mechanism, such as loop coverage or warning, should be in place for scenario where the size of logs is over the preset limit.¶
d) Only authenticated users have the privilege to view logs.¶
e) Log information should be presented in a form that is easy for users to understand.¶
The IoT smart device should check the validity of the input data, and this process should be carried out on the server.¶
a) For the smart device, internal sensitive information, such as passwords, configuration information, should be stored as cipher text.¶
b) For the smart device, sensitive information should be encrypted when transmitted.¶
c) For the smart device, log records and information printouts should not contain any sensitive information.¶
d) For the smart device, user interfaces for local, remote, web, and other operations should not show sensitive information.¶
a) The smart device should have unique network identifier.¶
b) If the device accesses the network layer via wireless networks, such as Wi-Fi, the wireless network protection mechanism, such as WPA2, should be applied.¶
a) The smart device should only enable the necessary network port by default.¶
b) All available network ports of the device should be open to users.¶
a) The smart device should apply secure protocols, including but not limited to TLS, HTTPS, SSH, SFTP, etc.¶
b) The smart device should remove high-risk services, including but not limited to telnet service, FTP service, etc.¶
c) The on-off mechanism of the service should be provided and be off by default when protocols with imperfect security mechanism are applied. A security risk alert is required when the user apply for the service using these insecure protocols.¶
d) If a Web service is provided, the Web security mechanism should be implemented, including checking the validity of input and output, and taking measures to prevent code vulnerabilities such as authentication vulnerabilities, permission vulnerabilities, session vulnerabilities, injection vulnerabilities, file upload vulnerabilities, etc.¶
a) The smart device should allow the user to initiatively end the communication.¶
b) The session should be ended if there is no operation for a long duration, and the duration time can be set by the administrator.¶
c) The smart device should restrict the address of remote connections, such as IP address filtering, etc.¶
d) Limit the number of concurrent network connections.¶
a) The smart device should provide a trusted communication path (Such as TLS) for the remote user to protect the communication data from leakage.¶
b) Remote users should be allowed to initiate communication via a trusted path.¶
c) A trusted path is required when processing user authentication.¶
d) A trusted path between the device and another trusted IT product should be provided to protect communication data from modification or leakage.¶
The smart device should use cryptographic mechanisms to protect the integrity and confidentiality of video streams during transmission.¶
The smart device must employ cryptographic mechanisms to protect the integrity of applications running in it. Applications that have been tampered with or of unknown origin should be forbidden to run.¶
In the design and development phase, it requires security reviews for any third-party components (TPCs) embedded in the applications of smart devices.¶
a) The smart device should be able to be managed and configured remotely.¶
b) The smart device should be able to inquire and export log information.¶
c) The smart device should be able to upgrade firmware remotely.¶
d) The smart device should be able to manage activation/non-activation service remotely.¶
e) The smart device should follow a lifetime policy, which clarifies the security risks of overdue and declares that manufacturer will no longer update firmware of the device if overdue.¶
This entire memo deals with security issues.¶
This documents has no IANA actions.¶