Internet-Draft NETWORK-TESTER-MANAGEMENT-00 June 2022
Vassilev Expires 19 December 2022 [Page]
Workgroup:
Network Working Group
Internet-Draft:
draft-ietf-bmwg-network-tester-cfg-00
Published:
Intended Status:
Standards Track
Expires:
Author:
V. Vassilev
Lightside Instruments AS

A YANG Data Model for Network Tester Management

Abstract

This document introduces new YANG model for use in network interconnect testing containing modules of traffic generator and traffic analyzer.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 19 December 2022.

Table of Contents

1. Introduction

There is a need for standard mechanism to allow the specification and implementation of the transactions part of network tests. The mechanism should allow the control and monitoring of the data plane traffic in a transactional way. This document defines two YANG modules for test traffic generator and analyzer.

The YANG modules in this document conform to the Network Management Datastore Architecture (NMDA) defined in RFC 8342.

1.1. Terminology

1.1.1. Definitions and Acronyms

DUT: Device Under Test

TA: Traffic Analyzer

TG: Traffic Generator

1.1.2. Tree Diagram

For a reference to the annotations used in tree diagrams included in this document, please see YANG Tree Diagrams [RFC8340].

1.2. Problem Statement

Network interconnect tests require active network elements part of the tested network that generate test traffic and network elements that analyze the test traffic at one or more points of its path. A network interconnect tester is a device that can either generate test traffic, analyze test traffic or both. Here is a figure borrowed from [RFC2544] representing the horseshoe test setup topology consisting of a single tester and a single DUT connected in a network interconnect loop.

                 +------------+
                 |            |
    +------------|  tester    |<-------------+
    |            |            |              |
    |            +------------+              |
    |                                        |
    |            +------------+              |
    |            |            |              |
    +----------->|    DUT     |--------------+
                 |            |
                 +------------+

This document attempts to address the problem of defining YANG model of a network interconnect tester that can be used for development of vendor independent network interconnect tests and utilize the advantages of transactional management using standard protocols like NETCONF.

1.3. Objectives

This section describes some of the design objectives for the model. It should:

1.4. Solution

The proposed model splits the design into 2 modules - 1) Traffic Generator module (TG), 2) Traffic Analyzer module (TA). The modules are implemented as augmentations of the ietf-interfaces [RFC8343] module adding configuration and state data that models the functionality of a network interconnect tester. The TA and TG modules concept is illustrated with the following diagram of a tester with two interfaces (named e0 and e1) connected in a loop with single DUT:

                 +----------------+
       e0.egress |                | e1.ingress
    +------------| TG  tester  TA |<-------------+
    |            |                |              |
    |            +----------------+              |
    |                                            |
    |              +------------+                |
    |              |            |                |
    +------------->|    DUT     |----------------+
                   |            |
                   +------------+

2. Using the network interconnect tester model

Basic example of how the model can be used in transactional network test program to control the testers part of a network and report counter statistics and timing measurement data is presented in Appendix A. All example cases present the configuration and state data from a single test trial. The search algorithm logic that operates to control the trial configuration is outside the scope of this document. One of the examples demonstrates the use of the [RFC2544] defined testframe packet.

3. Traffic Generator Module Tree Diagram

module: ietf-traffic-generator
  augment /if:interfaces/if:interface:
    +--rw traffic-generator {egress-direction}?
    |  +--rw (type)?
    |  |  +--:(single-stream)
    |  |  |  +--rw testframe-type?     identityref
    |  |  |  +--rw frame-size          uint32
    |  |  |  +--rw frame-data?         string
    |  |  |  +--rw interframe-gap      uint32
    |  |  |  +--rw interburst-gap?     uint32
    |  |  |  +--rw frames-per-burst?   uint32
    |  |  |  +--rw src-mac-address?    yang:mac-address {ethernet}?
    |  |  |  +--rw dst-mac-address?    yang:mac-address {ethernet}?
    |  |  |  +--rw ether-type?         uint16 {ethernet}?
    |  |  +--:(multi-stream)
    |  |     +--rw streams
    |  |        +--rw stream* [id]
    |  |           +--rw id                   uint32
    |  |           +--rw testframe-type?      identityref
    |  |           +--rw frame-size           uint32
    |  |           +--rw frame-data?          string
    |  |           +--rw interframe-gap       uint32
    |  |           +--rw interburst-gap?      uint32
    |  |           +--rw frames-per-burst?    uint32
    |  |           +--rw frames-per-stream    uint32
    |  |           +--rw interstream-gap      uint32
    |  |           +--rw src-mac-address?
    |  |           |       yang:mac-address {ethernet}?
    |  |           +--rw dst-mac-address?
    |  |           |       yang:mac-address {ethernet}?
    |  |           +--rw ether-type?          uint16 {ethernet}?
    |  +--rw realtime-epoch?
    |  |       yang:date-and-time {realtime-epoch}?
    |  +--rw total-frames?             uint64
    +--rw traffic-generator-ingress {ingress-direction}?
       +--rw (type)?
       |  +--:(single-stream)
       |  |  +--rw testframe-type?     identityref
       |  |  +--rw frame-size          uint32
       |  |  +--rw frame-data?         string
       |  |  +--rw interframe-gap      uint32
       |  |  +--rw interburst-gap?     uint32
       |  |  +--rw frames-per-burst?   uint32
       |  |  +--rw src-mac-address?    yang:mac-address {ethernet}?
       |  |  +--rw dst-mac-address?    yang:mac-address {ethernet}?
       |  |  +--rw ether-type?         uint16 {ethernet}?
       |  +--:(multi-stream)
       |     +--rw streams
       |        +--rw stream* [id]
       |           +--rw id                   uint32
       |           +--rw testframe-type?      identityref
       |           +--rw frame-size           uint32
       |           +--rw frame-data?          string
       |           +--rw interframe-gap       uint32
       |           +--rw interburst-gap?      uint32
       |           +--rw frames-per-burst?    uint32
       |           +--rw frames-per-stream    uint32
       |           +--rw interstream-gap      uint32
       |           +--rw src-mac-address?
       |           |       yang:mac-address {ethernet}?
       |           +--rw dst-mac-address?
       |           |       yang:mac-address {ethernet}?
       |           +--rw ether-type?
       |                   uint16 {ethernet}?
       +--rw realtime-epoch?
       |       yang:date-and-time {realtime-epoch}?
       +--rw total-frames?             uint64

4. Traffic Analyzer Module Tree Diagram

module: ietf-traffic-analyzer
  augment /if:interfaces/if:interface:
    +--rw traffic-analyzer! {ingress-direction}?
    |  +--rw filter! {filter}?
    |  |  +--rw type          identityref
    |  |  +--rw ether-type?   uint16
    |  +--rw capture {capture}?
    |  |  +--rw start-trigger
    |  |  |  +--rw (start-trigger)?
    |  |  |     +--:(frame-index)
    |  |  |     |  +--rw frame-index?       uint64
    |  |  |     +--:(testframe-index)
    |  |  |        +--rw testframe-index?   uint64
    |  |  +--rw stop-trigger
    |  |     +--rw (stop-trigger)?
    |  |        +--:(when-full)
    |  |           +--rw when-full?   empty
    |  +--ro state
    |     +--ro pkts?              yang:counter64
    |     +--ro octets?            yang:counter64
    |     +--ro idle-octets?       yang:counter64 {idle-octets-counter}?
    |     +--ro errors?            yang:counter64
    |     +--ro testframe-stats
    |     |  +--ro testframe-pkts?    yang:counter64
    |     |  +--ro sequence-errors?   yang:counter64
    |     |  +--ro payload-errors?    yang:counter64
    |     |  +--ro latency
    |     |     +--ro samples?   uint64
    |     |     +--ro min?       uint64
    |     |     +--ro max?       uint64
    |     |     +--ro average?   uint64
    |     |     +--ro latest?    uint64
    |     +--ro capture {capture}?
    |        +--ro frame* [sequence-number]
    |           +--ro sequence-number             uint64
    |           +--ro timestamp?                  yang:date-and-time
    |           +--ro length?                     uint32
    |           +--ro preceding-interframe-gap?   uint32
    |           +--ro data?                       string
    +--rw traffic-analyzer-egress! {egress-direction}?
       +--rw filter! {filter}?
       |  +--rw type    identityref
       +--rw capture {capture}?
       |  +--rw start-trigger
       |  |  +--rw (start-trigger)?
       |  |     +--:(frame-index)
       |  |     |  +--rw frame-index?       uint64
       |  |     +--:(testframe-index)
       |  |        +--rw testframe-index?   uint64
       |  +--rw stop-trigger
       |     +--rw (stop-trigger)?
       |        +--:(when-full)
       |           +--rw when-full?   empty
       +--ro state
          +--ro pkts?              yang:counter64
          +--ro octets?            yang:counter64
          +--ro idle-octets?       yang:counter64 {idle-octets-counter}?
          +--ro errors?            yang:counter64
          +--ro testframe-stats
          |  +--ro testframe-pkts?    yang:counter64
          |  +--ro sequence-errors?   yang:counter64
          |  +--ro payload-errors?    yang:counter64
          |  +--ro latency
          |     +--ro samples?   uint64
          |     +--ro min?       uint64
          |     +--ro max?       uint64
          |     +--ro average?   uint64
          |     +--ro latest?    uint64
          +--ro capture {capture}?
             +--ro frame* [sequence-number]
                +--ro sequence-number             uint64
                +--ro timestamp?                  yang:date-and-time
                +--ro length?                     uint32
                +--ro preceding-interframe-gap?   uint32
                +--ro data?                       string

5. Traffic Generator Module YANG

<CODE BEGINS> file "ietf-traffic-generator@2022-06-17.yang"

module ietf-traffic-generator {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-traffic-generator";
  prefix nttg;

  import ietf-interfaces {
    prefix if;
    reference
      "RFC 8343: A YANG Data Model For Interface Management";
  }
  import ietf-yang-types {
    prefix yang;
    reference
      "RFC 6991: Common YANG Data Types";
  }
  import iana-if-type {
    prefix ianaift;
    reference
      "RFC 7224: IANA Interface Type YANG Module";
  }

  organization
    "IETF Benchmarking Methodology Working Group";
  contact
    "WG Web:   <http://tools.ietf.org/wg/bmwg/>
     WG List:  <mailto:bmwg@ietf.org>

     Editor:   Vladimir Vassilev
               <mailto:vladimir@lightside-instruments.com>";
  description
    "This module contains a collection of YANG definitions for
     description and management of network interconnect testers.

     Copyright (c) 2021 IETF Trust and the persons identified as
     authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (http://trustee.ietf.org/license-info).
     This version of this YANG module is part of RFC XXXX; see
     the RFC itself for full legal notices.";

  revision 2022-06-17 {
    description
      "Initial revision.";
    reference
      "RFC XXXX: A YANG Data Model for
       Network Tester Management";
  }

  feature egress-direction {
    description
      "The device can generate traffic in the egress direction.";
  }

  feature ingress-direction {
    description
      "The device can generate traffic in the ingress direction.";
  }

  feature multi-stream {
    description
      "The device can generate multi-stream traffic.";
  }

  feature ethernet {
    description
      "The device can generate ethernet traffic.";
  }

  feature realtime-epoch {
    description
      "The device can generate traffic precisely
       at configured realtime epoch.";
  }

  identity testframe-type {
    description
      "Base identity for all testframe types.";
  }

  identity static {
    base testframe-type;
    description
      "Identity for static testframe.
       The frame data and size are constant.";
  }

  identity dynamic {
    base testframe-type;
    description
      "Identity to be used as base for dynamic
       testframe type identities defined
       in external modules.

       When used itself it identifies dynamic testframe
       where the last 18 octets of the payload contain
       incrementing sequence number field (8 octets)
       followed by timestamp field in the
       IEEE 1588-2008 format (10 octets). If frame data is defined
       for the last 18 octets of the payload it will be ignored
       and overwritten with dynamic data according to this
       specification.";
  }

  grouping common-data {
    description
      "Common configuration data.";
    leaf realtime-epoch {
      if-feature "realtime-epoch";
      type yang:date-and-time;
      description
        "If this leaf is present the stream generation will start
         at the specified realtime epoch.";
    }
    leaf total-frames {
      type uint64;
      description
        "If this leaf is present the traffic generation will stop
         after the specified number of frames are generated.";
    }
  }

  grouping burst-data {
    description
      "Generated traffic burst parameters.";
    leaf testframe-type {
      type identityref {
        base nttg:testframe-type;
      }
      default "nttg:static";
      description
        "In case of dynamic testframes this leaf specifies
         the dynamic testframe identity.";
    }
    leaf frame-size {
      type uint32;
      mandatory true;
      description
        "Size of the frames generated. For example for
         ethernet interfaces the following definition
         applies:

         Ethernet frame-size in octets includes:
         * Destination Address (6 octets),
         * Source Address (6 octets),
         * Frame Type (2 octets),
         * Data (min 46 octets or 42 octets + 4 octets 802.1Q tag),
         * CRC Checksum (4 octets).

         Ethernet frame-size does not include:
         * Preamble (dependent on MAC configuration
                    by default 7 octets),
         * Start of frame delimiter (1 octet)

         Minimum standard ethernet frame-size is 64 bytes but
         generators might support smaller sizes for validation.";
    }
    leaf frame-data {
      type string {
        pattern '([0-9A-F]{2})*';
      }
      must 'string-length(.)<=(../frame-size*2)';
      description
        "The raw  frame data specified as hexadecimal string.
         The specified data can be shorter then the ../frame-size
         value specifying only the header or the header and the
         payload with or without the 4 byte CRC Checksum
         in the case of a Ethernet frame.";
    }
    leaf interframe-gap {
      type uint32;
      mandatory true;
      description
        "Length of the idle period between generated frames.
         For example for ethernet interfaces the following
         definition applies:

         Ethernet interframe-gap between transmission of frames
         known as the interframe gap (IFG). A brief recovery time
         between frames allows devices to prepare for
         reception of the next frame. The minimum
         interframe gap is 96 bit times (12 octet times) (the time it
         takes to transmit 96 bits (12 octets) of raw data on the
         medium). However the preamble (7 octets) and start of
         frame delimiter (1 octet) are considered a constant gap that
         should be included in the interframe-gap. Thus the minimum
         value for standard ethernet transmission should be considered
         20 octets.";
    }
    leaf interburst-gap {
      type uint32;
      description
        "Similar to the interframe-gap but takes place between
         any two bursts of the stream.";
    }
    leaf frames-per-burst {
      type uint32;
      description
        "Number of frames contained in a burst";
    }
  }

  grouping multi-stream-data {
    description
      "Multi stream traffic generation parameters.";
    container streams {
      description
        "Non-presence container holding the configured stream list.";
      list stream {
        key "id";
        description
          "Each stream repeats a burst until frames-per-stream
           count is reached followed by interstream-gap delay.";
        leaf id {
          type uint32;
          description
            "Number specifying the order of the stream.";
        }
        uses burst-data;
        leaf frames-per-stream {
          type uint32;
          mandatory true;
          description
            "The count of frames to be generated before
             generation of the next stream is started.";
        }
        leaf interstream-gap {
          type uint32;
          mandatory true;
          description
            "Idle period after the last frame of the last burst.";
        }
      }
    }
  }

  grouping ethernet-data {
    description
      "Ethernet frame data specific parameters.";
    reference
      "IEEE 802-2014 Clause 9.2";
    leaf src-mac-address {
      type yang:mac-address;
      description
        "Source Address field of the generated Ethernet packet.";
    }
    leaf dst-mac-address {
      type yang:mac-address;
      description
        "Destination Address field of the generated Ethernet packet.";
    }
    leaf ether-type {
      type uint16;
      description
        "Length/Type field of the generated Ethernet packet.";
    }
  }

  augment "/if:interfaces/if:interface" {
    description
      "Traffic generator augmentations of ietf-interfaces.";
    container traffic-generator {
      if-feature "egress-direction";
      description
        "Traffic generator for egress direction.";
      choice type {
        description
          "Choice of the type of the data model of the generator.
           Single or multi stream.";
        case single-stream {
          uses burst-data;
        }
        case multi-stream {
          uses multi-stream-data;
        }
      }
      uses common-data;
    }
    container traffic-generator-ingress {
      if-feature "ingress-direction";
      description
        "Traffic generator for ingress direction.";
      choice type {
        description
          "Choice of the type of the data model of the generator.
           Single or multi stream.";
        case single-stream {
          uses burst-data;
        }
        case multi-stream {
          uses multi-stream-data;
        }
      }
      uses common-data;
    }
  }

  augment "/if:interfaces/if:interface/nttg:traffic-generator/"
        + "nttg:type/nttg:single-stream" {
    when "derived-from-or-self(../if:type, 'ianaift:ethernetCsmacd')" {
      description
        "Ethernet interface type.";
    }
    if-feature "ethernet";
    description
      "Ethernet specific augmentation for egress
       single stream generator type.";
    uses ethernet-data;
  }

  augment "/if:interfaces/if:interface/nttg:traffic-generator/"
        + "nttg:type/nttg:multi-stream/nttg:streams/nttg:stream" {
    when "derived-from-or-self(../../../if:type,"
       + "'ianaift:ethernetCsmacd')" {
      description
        "Ethernet interface type.";
    }
    if-feature "ethernet";
    description
      "Ethernet specific augmentation for egress
       multi stream generator type.";
    uses ethernet-data;
  }

  augment "/if:interfaces/if:interface/nttg:traffic-generator-ingress/"
        + "nttg:type/nttg:single-stream" {
    when "derived-from-or-self(../if:type, 'ianaift:ethernetCsmacd')" {
      description
        "Ethernet interface type.";
    }
    if-feature "ethernet";
    description
      "Ethernet specific augmentation for ingress
       single stream generator type.";
    uses ethernet-data;
  }

  augment "/if:interfaces/if:interface/nttg:traffic-generator-ingress/"
        + "nttg:type/nttg:multi-stream/nttg:streams/nttg:stream" {
    when "derived-from-or-self(../../../if:type,"
       + "'ianaift:ethernetCsmacd')" {
      description
        "Ethernet interface type.";
    }
    if-feature "ethernet";
    description
      "Ethernet specific augmentation for ingress
       multi stream generator type.";
    uses ethernet-data;
  }
}

<CODE ENDS>

6. Traffic Analyzer Module YANG

<CODE BEGINS> file "ietf-traffic-analyzer@2022-06-17.yang"

module ietf-traffic-analyzer {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-traffic-analyzer";
  prefix ntta;

  import ietf-interfaces {
    prefix if;
    reference
      "RFC 8343: A YANG Data Model For Interface Management";
  }
  import ietf-yang-types {
    prefix yang;
    reference
      "RFC 6991: Common YANG Data Types";
  }

  organization
    "IETF Benchmarking Methodology Working Group";
  contact
    "WG Web:   <http://tools.ietf.org/wg/bmwg/>
     WG List:  <mailto:bmwg@ietf.org>

     Editor:   Vladimir Vassilev
               <mailto:vladimir@lightside-instruments.com>";
  description
    "This module contains a collection of YANG definitions for
     description and management of network interconnect testers.

     Copyright (c) 2021 IETF Trust and the persons identified as
     authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (http://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC XXXX; see
     the RFC itself for full legal notices.";

  revision 2022-06-17 {
    description
      "Initial revision.";
    reference
      "RFC XXXX: A YANG Data Model for
       Network Tester Management";
  }

  feature egress-direction {
    description
      "The device can analyze traffic from the egress direction.";
  }

  feature ingress-direction {
    description
      "The device can generate traffic from the ingress direction.";
  }

  feature filter {
    description
      "This feature indicates that the device implements
       filter that can specify a subset of packets to be
       analyzed when filtering is enabled.";
  }

  feature idle-octets-counter {
    description
      "This feature indicates that the device implements
       idle-octets counter that accumulates the time
       the link is not utilized. The minimum required
       idle gaps are not counted as idle octets.";
  }
  feature capture {
    description
      "This feature indicates that the device implements
       packet capture functionality.";
  }

  identity filter {
    description
      "Base filter identity.";
  }

  identity ethernet {
    base ntta:filter;
    description
      "Ethernet packet fields filter.";
  }

  grouping statistics-data {
    description
      "Analyzer statistics.";
    leaf pkts {
      type yang:counter64;
      description
        "Total number of packets analyzed.";
    }
    leaf octets {
      type yang:counter64;
      description
        "This counter is identical with the in-octets/out-octets
         counters defined in RFC8343 except that it counts the
         octets since the analyzer was created.";
    }
    leaf idle-octets {
      if-feature "idle-octets-counter";
      type yang:counter64;
      description
        "Total accumulated period with no frame transmission
         taking place measured in octets at the current link
         speed. Octets not counted in ../octets but not idle are
         for example layer 1 framing octets - for Ethernet links
         7+1 preamble octets per packet.";
    }
    leaf errors {
      type yang:counter64;
      description
        "Count of packets with errors.
         Not counted in the pkts or captured.
         For example packets with CRC error.";
    }
    container testframe-stats {
      description
        "Statistics for testframe packets containing
         either sequence number, payload checksum,
         timestamp or any combination of these features.";
      leaf testframe-pkts {
        type yang:counter64;
        description
          "Total count of detected testframe packets.";
      }
      leaf sequence-errors {
        type yang:counter64;
        description
          "Total count of testframe packets with
           unexpected sequence number. After each sequence
           error the expected next sequence number is
           updated.";
      }
      leaf payload-errors {
        type yang:counter64;
        description
          "Total count of testframe packets with
           payload errors.";
      }
      container latency {
        description
          "Latency statistics.";
        leaf samples {
          type uint64;
          description
            "Total count of packets used for estimating
             the latency statistics. Ideally
             samples=../testframe-stats.";
        }
        leaf min {
          type uint64;
          units "nanoseconds";
          description
            "Minimum measured latency.";
        }
        leaf max {
          type uint64;
          units "nanoseconds";
          description
            "Maximum measured latency.";
        }
        leaf average {
          type uint64;
          units "nanoseconds";
          description
            "The sum of all sampled latencies divided
             by the number of samples.";
        }
        leaf latest {
          type uint64;
          units "nanoseconds";
          description
            "Latency of the latest sample.";
        }
      }
    }
  }

  grouping capture-config-data {
    description
      "Grouping with a capture configuration container.";
    container capture {
      if-feature "capture";

      description
        "Contains capture parameters.";

      container start-trigger {
          description
            "Configures when the capture start is triggered.";
        choice start-trigger {
          description
            "If none of the cases in this choice are configured the
             capture process starts from the first frame received.";
          case frame-index {
            description
              "Start capturing frames at the specified frame index.";
            leaf frame-index {
              type uint64;
              description
                "First captured frame index.";
            }
          }
          case testframe-index {
            description
              "Start capturing frames at the specified
               testframe index.";
            leaf testframe-index {
              type uint64;
              description
                "Starts capture as specified testframe index.";
            }
          }
        }
      }
      container stop-trigger {
          description
            "Configures when the capture is stopped.";
        choice stop-trigger {
          description
            "If none of the cases in this choice are configured the
             captured frames are always the last frames received for
             as many frames the implementation can buffer.";
          case when-full {
            description
              "Stops capturing when the implementation can not store
               more frames.";
            leaf when-full {
                type empty;
                description
                  "When present in configuration capture stops when
                   the capture buffer is full.";
            }
          }
        }
      }
    }
  }

  grouping capture-data {
    description
      "Grouping with statistics and data
       of one or more captured frame.";
    container capture {
      if-feature "capture";
      description
        "Statistics and data of
         one or more captured frames.";
      list frame {
        key "sequence-number";
        description
          "Statistics and data of a captured frame.";
        leaf sequence-number {
          type uint64;
          description
            "Incremental counter of frames captured.";
        }
        leaf timestamp {
          type yang:date-and-time;
          description
            "Timestamp of the moment the frame was captured.";
        }
        leaf length {
          type uint32;
          description
            "Frame length. Ideally the data captured will be
             of the same length but can be shorter
             depending on implementation limitations.";
        }
        leaf preceding-interframe-gap {
          type uint32;
          units "nanoseconds";
          description
            "Measured delay between the reception of the previous
             frame was completed and the reception of the current
             frame was started.";
        }
        leaf data {
          type string {
            pattern '([0-9A-F]{2})*';
          }
          description
            "Raw data of the captured frame.";
        }
      }
    }
  }

  grouping filter-data {
    description
      "Grouping with a filter container specifying the filtering
       rules for processing only a specific subset of the
       frames.";
    container filter {
      if-feature "filter";
      presence "When present packets are
                filtered before analyzed according
                to the filter type";
      description
        "Contains the filtering rules for processing only
         a specific subset of the frames.";
      leaf type {
        type identityref {
          base ntta:filter;
        }
        mandatory true;
        description
          "Type of the applied filter. External modules can
           define alternative filter type identities.";
      }
    }
  }

  augment "/if:interfaces/if:interface" {
    description
      "Traffic analyzer augmentations of ietf-interfaces.";
    container traffic-analyzer {
      if-feature "ingress-direction";
      presence "Enables the traffic analyzer for ingress traffic.";
      description
        "Traffic analyzer for ingress direction.";
      uses filter-data;
      uses capture-config-data;
      container state {
        config false;
        description
          "State data.";
        uses statistics-data;
        uses capture-data;
      }
    }
    container traffic-analyzer-egress {
      if-feature "egress-direction";
      presence "Enables the traffic analyzer for egress traffic.";
      description
        "Traffic analyzer for egress direction.";
      uses filter-data;
      uses capture-config-data;
      container state {
        config false;
        description
          "State data.";
        uses statistics-data;
        uses capture-data;
      }
    }
  }

  augment "/if:interfaces/if:interface/ntta:traffic-analyzer/"
        + "ntta:filter" {
    when "derived-from-or-self(ntta:type, 'ntta:ethernet')";
    description
      "Ethernet frame specific filter type.";
    leaf ether-type {
      type uint16;
      description
        "The Ethernet Type (or Length) value
         defined by IEEE 802.";
      reference
        "IEEE 802-2014 Clause 9.2";
    }
  }
}

<CODE ENDS>

7. IANA Considerations

This document registers two URIs and two YANG modules.

7.1. URI Registration

This document registers two URIs in the IETF XML registry [RFC3688]. Following the format in RFC 3688, the following registration is requested to be made:

URI: urn:ietf:params:xml:ns:yang:ietf-traffic-generator
URI: urn:ietf:params:xml:ns:yang:ietf-traffic-analyzer

Registrant Contact: The IESG.

XML: N/A, the requested URI is an XML namespace.

7.2. YANG Module Name Registration

This document registers two YANG module in the YANG Module Names registry YANG [RFC6020].

name: ietf-traffic-generator
namespace: urn:ietf:params:xml:ns:yang:ietf-traffic-generator
prefix: nttg
reference: RFC XXXX

name: ietf-traffic-analyzer
namespace: urn:ietf:params:xml:ns:yang:ietf-traffic-analyzer
prefix: ntta
reference: RFC XXXX

8. Security Considerations

The YANG modules defined in this document are designed to be accessed via the NETCONF protocol RFC 6241 [RFC6241]. The lowest NETCONF layer is the secure transport layer and the mandatory to implement secure transport is SSH RFC 6242 [RFC6242]. The NETCONF access control model RFC 6536 [RFC6536] provides the means to restrict access for particular NETCONF users to a pre-configured subset of all available NETCONF protocol operations and content.

There are a number of data nodes defined in this YANG module which are writable/creatable/deletable (i.e. config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g. edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability:

8.1. ietf-traffic-generator.yang

The ietf-traffic-generator YANG module controls a stateless traffic generator which is intended to be used for testing and verification purposes but can be used for malicious purposes like generating network traffic part of a Denial-of-Service (DoS) attack. This should be taken into consideration when granting write access to the following container and descendant data nodes:

  • /if:interfaces/if:interface/nttg:traffic-generator

8.2. ietf-traffic-analyzer.yang

The ietf-traffic-analyzer YANG module controls a traffic analyzer which is designed for use in testing and verification but can be used for reading information contained in packets sent and received on any of the interfaces on systems that implement the capture feature. This should be taken into consideration when granting read access to the following container and descendant data nodes:

  • /if:interfaces/if:interface/ntta:traffic-analyzer/ntta:capture

9. References

9.1. Normative References

[RFC6020]
Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/info/rfc6020>.
[RFC6241]
Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, , <https://www.rfc-editor.org/info/rfc6241>.
[RFC6242]
Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, , <https://www.rfc-editor.org/info/rfc6242>.
[RFC6536]
Bierman, A. and M. Bjorklund, "Network Configuration Protocol (NETCONF) Access Control Model", RFC 6536, DOI 10.17487/RFC6536, , <https://www.rfc-editor.org/info/rfc6536>.
[RFC6991]
Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, , <https://www.rfc-editor.org/info/rfc6991>.
[RFC7224]
Bjorklund, M., "IANA Interface Type YANG Module", RFC 7224, DOI 10.17487/RFC7224, , <https://www.rfc-editor.org/info/rfc7224>.
[RFC7950]
Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, , <https://www.rfc-editor.org/info/rfc7950>.
[RFC8343]
Bjorklund, M., "A YANG Data Model for Interface Management", RFC 8343, DOI 10.17487/RFC8343, , <https://www.rfc-editor.org/info/rfc8343>.

9.2. Informative References

[IEEE1588]
IEEE, "IEEE 1588-2008", .
[IEEE802.3-2014]
IEEE WG802.3 - Ethernet Working Group, "IEEE 802.3-2014", .
[RFC2544]
Bradner, S. and J. McQuaid, "Benchmarking Methodology for Network Interconnect Devices", RFC 2544, DOI 10.17487/RFC2544, , <https://www.rfc-editor.org/info/rfc2544>.
[RFC3688]
Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, , <https://www.rfc-editor.org/info/rfc3688>.
[RFC8340]
Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, , <https://www.rfc-editor.org/info/rfc8340>.

Appendix A. Examples

The following topology will be used for the examples in this section:

    +-------------+          +------------+         +------------+
    |             | e0    e0 |            | e1   e0 |            |
    | tester0   TG|>-------->|    dut0    |>------->|TA  tester1 |
    |             |          |            |         |            |
    +-------------+          +------------+         +------------+

A.1. Basic Test Program

This pseudo code program orchestrates a network test and shows how the model can be used:

#Connect to network
net=connect("topology.xml")

# Configure DUTs and enable traffic-analyzers
net.node("dut0").edit( \
  "create /interfaces/interface[name='e0'] -- type=ethernetCsmacd")
net.node("dut0").edit(
  "create /interfaces/interface[name='e1'] -- type=ethernetCsmacd")
net.node("dut0").edit(
  "create /flows/flow[id='t0'] -- match/in-port=e0 "
  "actions/action[order='0']/output-action/out-port=e1")

net.node("tester1").edit(
  "create /interfaces/interface[name='e0']/traffic-analyzer")
net.commit()

#Get network state - before
before=net.get()

# Start traffic
net.node("tester0).edit(
  "create /interfaces/interface[name='e0']/traffic-generator -- "
  "frame-size=64 interframe-gap=20")

net.commit()

time.sleep(60)

# Stop traffic
net.node("tester1").edit("delete /interfaces/interface[name='e0']/"
                         "traffic-generator")
net.commit()

#Get network state - after
after=net.get()

#Report
sent_pkts=delta("tester0",before,after,
  "/interfaces/interface[name='e0']/statistics/out-unicast-pkts")

received_pkts=delta("tester1",before,after,
  "/interfaces/interface[name='e0']/statistics/in-unicast-pkts")

latency_max=absolute(after,
  "/interfaces/interface[name='e0']/traffic-analyzer/state/"
  "testframe-stats/latency/max")

#Cleanup
net.node("tester1").edit(
   "delete /interfaces/interface/traffic-analyzer")
net.node("dut0").edit("delete /flows")
net.node("dut0").edit("delete /interfaces")
net.commit()

A.2. Generating RFC2544 Testframes

In sec. C.2.6.4 Test Frames a detailed format is specified. The frame-data leaf allows full control over the generated frames payload.

...
net.node("tester1").edit(
  "merge /interfaces/interface[name='e0']/"
  "traffic-generator -- frame-data="
  "6CA96F0000026CA96F00000108004500"
  "002ED4A500000A115816C0000201C000"
  "0202C0200007001A0000010203040506"
  "0708090A0B0C0D0E0F101112")
...

Author's Address

Vladimir Vassilev
Lightside Instruments AS