Internet-Draft PIM Light September 2022
Bidgoli, et al. Expires 24 March 2023 [Page]
Workgroup:
Network Working Group
Internet-Draft:
draft-ietf-pim-light-00
Published:
Intended Status:
Standards Track
Expires:
Authors:
H. Bidgoli, Ed.
Nokia
S. Venaas
Cisco System, Inc.
M. Mishra
Cisco System
Z. Zhang
Juniper Networks
M. McBride
Futurewei Technologies Inc.

PIM Light

Abstract

This document specifies a new Protocol Independent Multicast interface which does not need PIM Hello to accept PIM Join/Prunes.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 24 March 2023.

Table of Contents

1. Introduction

It might be desirable to create a PIM interface between routers where only PIM Join/Prunes packets are signaled over it without having a full PIM neighbor discovery. As an example, this type of PIM interface can be useful in some scenarios where the multicast state needs to be signaled over a network or medium which is not capable of or has no need for creating full PIM neighborship between its Peer Routers. These type of PIM interfaces are called PIM Light Interfaces (PLI).

2. Conventions used in this document

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

2.1. Definitions

This draft uses definitions used in [RFC7761]

3. PIM Light Interface

RFC [RFC7761] section 4.3.1 describes the PIM neighbor discovery via Hello messages. It also describes that PIM Join/Prune are not accepted from a router unless a Hello message has been seen from that router.

In some scenarios it is desirable to communicate and build multicast states between two directly or non directly attach routers without establishing a PIM neighborship. There could be many reasons for this desired, but one example is the desired to signal multicast states upstream, between two or more PIM Domains via a network or medium that is not optimized for PIM or does not require PIM Neighbor establishment. An example is a BIER network connecting multiple PIM domains. In these BIER networks PIM Join/prune messages are tunneled via bier as per [draft-ietf-bier-pim-signaling].

A PIM Light Interface (PLI) ONLY accepts Join/Prune messages from an unknown PIM router and it accepts these messages it without receiving a PIM Hello message form the router. Lack of Hello Messages on a PLI means there is no mechanism to learn about the neighboring PIM routers on each interface and their capabilities or run some of the basic algorithms like DR Election between the routers. As such the router doesn't create any General-Purpose state for neighboring PIM and it only process Join/Prune message from downstream routers in its multicast routing table.

Because of this, a PLI needs to be created in very especial cases and the application that is using these PLIs should ensure there is no multicast duplication of packets. As an example, multiple upstream routers sending the same multicast stream to a single downstream router.

3.1. PLI supported Messages

As per IANA [iana_pim-parameters] PIM currently supports 12 message types, PIM Light only supports message type 3 (Join/Prune). All other message types are not supported for PIM Light and should not be process if received on a PLI.

3.1.1. PIM Sparse Mode

Lack of processing of register message on PLI means that, the Source, DR, RP all need to be in a common PIM domain and can not be connected over PIM Light domain. PLI will only processes join/prune regardless of if the join/prune is <S,G> or <*,G>.

3.2. Lack of Hello Message considration

The following should be considered on a PIM Light domain since hello messages are not processed.

3.2.1. Join Attribute

Since PLI does not process the pim hello message, processing of the join attributes option in pim hello as per [RFC5384] is also not supported, leaving PIM Light unaware of its neighbor capability of processing the join attribute. A PIM Light Router that does not understand the type 1 Encoded-source Address, should not process a join message that contains it. Otherwise the PLI can process the Join Attribute accordingly.

3.2.2. DR Selection

Since DR selection is not supported on PIM Light because of lack of hello messages, the network design should ensure that DR Election is achieve on the PIM domain, assuming the PIM Light domain is connecting PIM domains.

As an example, in a BIER domain which is connecting 2 PIM networks, a PLI can be used between the BIER edge routers. The PLI will be only used for multicast states communication, by transmitting ONLY PIM Join/prunes over the BIER domain. In this case to ensure there is no multicast stream duplication the PIM routers attached on each side of the BIER domain might want to establish PIM Adjacency via [RFC7761] to ensure DR election on the edge of the BIER router, while PLI is used in the BIER domain, between BIER edge routers. When the Join or Prune message arrives from a PIM domain to the down stream BIER edge router, it can be send over the BIER tunnel to the upstream BIER edge router only via the selected designated router.

3.3. PLI Configuration

Since a PLI doesn't require PIM Hello Messages and PIM neighbor adjacency is not checked for join/prune messages, there needs to be a mechanism to enable PLI on interfaces for security purpose, while on some other interfaces this may be enabled automatically. An example of the latter is the logical interface for a BIER sub-domain [draft-ietf-bier-pim-signaling].

If a system explicitly needs a PLI to be configured, then this system should not accepts the Join/Prune messages on interfaces that the PLI is not configured on, and it should drop these messages on a non PLI interface. If the system automatically enables PLI on some special interfaces, as an example interfaces facing a BIER domain, then it should accept Join/Prune messages on these interfaces only.

3.4. Failures in PLR domain

Because the hello messages are not processed on the PLI, some failures may not be discovered in PLI domain and multicast routes will not be pruned toward the source on the PIM domain, leaving the upstream routers continuously sending multicast streams.

Other protocols can be used to detect these failures in the PIM Light domain and they can be implementation specific. As an example, the interface that PIM Light is configured on can be protected via BFD or similar technology. If BFD to the far-end PLI goes down, and the Pim Light Router is upstream and is an OIF for a multicast route <S,G>, PIM should remove that PLI from its OIF list. In addition if upstream PLI is configured automatically, as an example in BIER case, when the downstream BFR is no longer reachable, the upstream PIM Light Router can prune the <S,G> advertised by that BFR, toward the source to stop the transmission of the multicast stream.

4. IANA Considerations

5. Security Considerations

6. Acknowledgments

Would like to thank Sandy <Zhang Zheng> for her suggestions and contribution to this draft.

7. References

7.1. Normative References

[draft-ietf-bier-pim-signaling]
"H.Bidgoli, F.XU, J. Kotalwar, I. Wijnands, M.Mishra, Z. Zhang, "PIM Signaling Through BIER Core"", .
[iana_pim-parameters]
"", .
[RFC2119]
"S. Brandner, "Key words for use in RFCs to Indicate Requirement Levels"", .
[RFC5384]
"A. Boers, I. Wijnands, E. Rosen "PIM Join Attribute Format"", .
[RFC7761]
"B.Fenner, M.Handley, H. Holbrook, I. Kouvelas, R. Parekh, Z.Zhang "PIM Sparse Mode"", .
[RFC8174]
"B. Leiba, "ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words"", .

7.2. Informative References

[RFC8279]
"Wijnands, IJ., Rosen, E., Dolganow, A., Przygienda, T. and S. Aldrin, "Multicast using Bit Index Explicit Replication"", .

Authors' Addresses

Hooman Bidgoli (editor)
Nokia
Ottawa
Canada
Stig
Cisco System, Inc.
San Jose,
United States of America
Mankamana Mishra
Cisco System
Milpitas,
United States of America
Zhaohui Zhang
Juniper Networks
Boston,
United States of America
Mike
Futurewei Technologies Inc.
Santa Clara,
United States of America